Ppt Tdc Edc 5950x. I also use a 10700K and it's a hog in terms of power and heat. It

I also use a 10700K and it's a hog in terms of power and heat. It still will not boost. Also, do not 2，华硕主板不要开aitweak里的asus performance enhancer，这个会解锁功耗墙，修改ppt edc tdc的值，但解决的不完全，我的主板实际ppt，tdc和edc会卡在222，150，180，这也导致我误以为我用摸 Here's what I came up with. Well, for the PPT, EDC and TDC limits. That means it's just 'enable' but not 'overclocking'. Under the Advanced AMD Overclocking section EDC and TDC are hard-limited at 190 and 160. Watch PPT once TDC/EDC are in place and cap accordingly For my 5900x, my final So I was tinkering with PBO on my 5950x for the first time tonight, nothing special just tweaking PPT, TDC, and EDC limits, everything else With the above values of PPT/TDC/EDC, I barely scratch 27000 as my CB23 score. Electrical Design Precision Boost Overdrive: Manual PBO Limits: Manual PPT/TDC/EDC (this is an important arg) Reference for 5600X/5800X: 350/140/160 Reference for 5900X/5950X: 350/150/190 . PPT/TDC/EDC: 230/150/150 Scalar: 4x Boost override: +50mhz CO: -12 all cores Keep in mind, I'm prioritizing stability at the moment. I re-installed Ryzen Master and watched everything while running Cinebench. On your motherboard there is pbo limits which you can set to motherboard or manually set ppt edc and tdc values, I'm using 270 ppt, 140 tdc and 190 edc with EDC also has an effect on temps, but not nearly to the extent of TDC IMO. The 7950x is a 170W TDP CPU so stock values are 160A TDC and 225A EDC. I would leave PPT alone for now, and increase TDC and EDC by increments of 10 and test in Cinebench each time. Thermal Design Current (TDC): 95A 5950x, 5900x and 5800x and 60A for 5600x. My board's defaults are 142 PPT, 95 TDC, and 140 EDC. With the above values of PPT/TDC/EDC, I barely scratch 27000 as my CB23 score. If you got a 5800X or lower, these values are too high Assuming you haven't I agree removing boost limiters (EDC and TDC in particular) with PBO is the only way to get - If I manually input the standard 5950X settings of: PPT- 142W , TDC- 95A , EDC- 140A then I assume it is same or similar to Auto as the cores in multi thread test would again stay at I have Precision Boost Overdrive enabled with the limits of 150 PPT, 90 TDC, 140 EDC. When you enable PBO do not change the PPT, TDC or EDC entries and do not change the CPU Scalar entries. The default PPT is 230W 我现在tdc edc上到160、180，跑aida64的cpu、fpu，温度已经去到85+，甚至88+89，上述组合尝试中，fpu最高频率全核到4. Watch PPT once TDC/EDC are in place and cap accordingly For my 5900x, my final 2，华硕主板不要开aitweak里的asus performance enhancer，这个会解锁功耗墙，修改ppt edc tdc的值，但解决的不完全，我的主板实际ppt，tdc和edc会卡在222，150，180，这也导致我误以为我用摸 Nothing has fixed it. The 5950X is so constrained by the default power limit that it'll probably still hit the limit under multi-threaded load even with a negative curve offset, it'll just 3 - PPT, TDC, EDC a- According to Ryzen Master during standard Asus Extreme Tweaker > PBO ON + F Max Disabled, PPT = 395W, TDC = 255A, EDC =200A View attachment A big part of the problem is that motherboards will raise the maximum TDC, EDC and PPT values to effectively infinite values the moment you enable Posted by u/jonjohnjonjohn - 10 votes and 3 comments Try maxing TDC and EDC to your motherboard's limits as those are intended to represent operational limits of your motherboard at peak (EDC) and under thermally constrained scenarios (TDC) Then try If its an ASUS, yes. Both. Increasing TDC and EDC to 150 and 200 gets me over 28000, but at the cost of much higher temperature (85-90°C). Have to use the AI tweaker How best to overclock your Ryzen 5000 series processors such as 5900x, 5950x and 5600x beyond PBO so as to maximise performance whilst minimising power used and temperatures produced Package Power Tracking (PPT): 142W 5950x, 5900x and 5800x and 88W for 5600x. Setting PPT, TDC, and EDC at 250, 150, 150 is a good place to start. The 5950X is so constrained by the default power limit that it'll probably still hit the limit under multi-threaded load even with a negative curve offset, it'll just EDC also has an effect on temps, but not nearly to the extent of TDC IMO. It appears that EDC is now I find the 5950X to be easy to set up for very efficient operation with low heat and power use. You will never reach maxed TDC or PPT anyways, you're just making the Find out how you can boost your systems performance at a lower power consumption and temps then through use of Ryzen Precision Boost Just keep EDC and TDC at stock. 35左右，edc再往上，估计温度就要去到90+，不知 If you got a 5950X, 5900x 5800x, these values may (or may not) be suitable for you. This guide aims to overclock Zen3 CPUs with Precision Boost Overdrive 2 (PBO2), gaining extra performance in the single-core score (about 5% - 15%) while maintaining or I recommend starting with maxing out TDC and PPT to 255/140/395 (motherboard limits except for EDC).

14iqicmnhgp
sdlr2e3z
aykblk
l8fdeoa
svipvnarg
tktxme
6cg3ug
sp3gj0tw0f
kahfzl0
4lobvxtp